program

Plenary meeting

(Large conference hall)

Chairman:

Evgeny N. Kablov – Academician of RAS,

Director General of FSUE «VIAM» SRF RF

Deputy Chairman:

Olga G. OspennikovaCand.of Sc. (Tech.), Head of SRB «Heat-resistant
cast and wrought alloys and steels, protective
coatings for GTE components» FSUE «VIAM» SRC RF

09:00–10:00

Registration of participants

10:00–10:10

Opening of the conference. Welcoming speech

 

Academician of RAS, Professor, Dr. of Sc. (Tech.)
Evgeny N. Kablov

(FSUE «VIAM» SRC RF)

10:10–10:20

Welcoming speech

Academician of RAS, Professor, Dr. of Sc. (Chem.)
Yuri M. Mikhailov

(Scientific and Technical Council under the Military-Industrial

Commission of the Russian Federation)

10:20–10:30

Welcoming speech

 

Dr. of Sc. (Tech.) Andrei I. Grigoriev
(Advanced Research Foundation)

10:30–10:40

Welcoming speech

 

Cand. of Sc.(Econ.)  Andrei I. Boginskiy
(Ministry of Industry and Trade of RF)

10:40–10:50

Welcoming speech

 

Sergey V. Salikhov
(Ministry of Education and Science of RF)

10:50–11:20

Additive technologies: present-day and the future

 

Academician of RAS, Professor, Dr. of Sc. (Tech.)
Evgeny N. Kablov

(FSUE «VIAM» SRC RF)

11:20–11:50

Experience on application and prospects for development of additive technologies
 

Corresponding member of RAS, Professor, Dr. of Sc. (Tech.)
Andrei I.  Rudskoy

 (Peter the Great St. Petersburg Polytechnic University)

11:50–13:00

Lunch break.

The beginning of work of the stand section

 

Section №1

«Materials and additive technologies of manufacturing of parts»

(Large conference hall)

Chief of the section:

Olga G. OspennikovaCand.of Sc. (Tech.), Head of SRB «Heat-resistant
cast and wrought alloys and steels, protective
coatings for GTE components»

FSUE «VIAM» SRC RF

Academic Secretary:

Alexander G. Evgenov Cand.of Sc. (Tech.), Head of laboratory «Powder metallurgy and additive production»
FSUE «VIAM» SRC RF

13:00–13:10

Structure and properties of Ni-based alloys produced by the method of SLM

 

Cand.of Sc. (Tech.) Alexander G. Evgenov

(FSUE «VIAM» SRC RF),

Cand.of Sc. (Tech.) E.A. Lukina

13:10–13:20

Stress-strain state and topological optimization of bracket produced by the method of selective laser melting

 

Dr. of Sc. (Tech.)Nikolai A. Trufanov

(Perm National Research Polytechnic University),
R.N. Faskhutdinov,
Cand.of Sc. (Tech.) А.S. Dubrovskaya

13:20–13:30

Additive technologies for ceramic MEMS-based sensors

 

Dr. of Sc. (Tech.)Aleksey А. Vasiliev

(NRC «Kurchatov Institute» SRC RF),

А.V. Sokolov, Cand.of Sc. (Tech.) N.N. Samotaev, K.Yu. Oblov,

V.P. Kim, Cand. of Sc. (Chem.) S.V. Tkachev, Dr. of Sc. (Chem.)S.P. Gubin,
 G.N. Potapov, Yu.V. Kokhtina,
Cand.of Sc. (Tech.) А.V. Nisan

13:30–13:40

Production of powders on the basis of titanium for additive technologies

 

Cand.of Sc. (Tech.) Vladimir I.  Kotlyarov
(JSC «Giredmet»),

Cand.of Sc. (Tech.) А.V. Samokhin, Cand.of Sc. (Tech.) V.Е. Кartsev,
Cand.of Sc. (Tech.) V.T. Beshkarev,  V.V. Ivanov, Cand. of Sc. (Chem.) А.А. Gasanov, 
E.A. Yuzhakova, 
А.А. Fadeev, M.А. Sinayskiy, 
Cand.of Sc. (Tech.) N.V. Alekseev, R.Yu. Kozlov

13:40–13:50

Additive technologies in endoprosthesis replacement: from mold making to implant

 

Professor, Dr. of Sc. (Tech.) Sergey S.  Gavryushin

(Bauman Moscow State Technical University,

LLC «New technologies»),
S.S. Hrykov

13:50–14:00

Additive technologies – art or new direction in development of industry?

 

Dr. of Sc. (Tech.)Pavel A. Kuznetsov
(FSUE «CRISM „Prometey”»),
Dr. of Sc. (Tech.)
А.S. Oryshchenko

14:00–14:10

Production of aerospace model engineering as a tool for development of additive technologies

 

Cand.of Sc. (Tech.) Tatyana S. Volchenko

(FFE «Аleksinsky chemical plant»)

14:10–14:20

Influence of technological process parameters of selective laser melting on patterning of heat-resistant nickel alloy

 

Cand.of Sc. (Tech.) Elena B. Chabina

(FSUE «VIAM» SRC RF),

Е.V. Filonova, А.N. Raevskikh

14:20–14:30

Experience on application of additive technologies at OJSC «Aviadvigatel»

 

Rustam N. Faskhutdinov

(OJSC «Aviadvigatel»),

А.G. Аksenov, Yu.V. Samusina

14:30–14:40

Implementation of additive technologies at NPO «Saturn»

 

Denis V. Fedoseev

(PJSC «NPO „Saturn”»)

14:40–14:50

Experience of OJSC «Composite» in the field of production of articles from domestic alloy VT6C using the method of selective electron-beam melting  

 

Zhanna А. Sentyurina

(OJSC «Composite»),

Cand.of Sc. (Tech.) А.I. Logacheva, Cand.of Sc. (Tech.) I.А. Logachev, P.А. Usov

14:50–15:10

Research of material produced by using SLS technology from powder of titanium alloy 64ELI

 

Andrey D. Farafontov

(PJSC «Corporation  «VSMPO-AVISMA»),

А.G. Merkushev

15:00–15:10

New thermoplastic material with reduced fire hazard for FDM-technologies

 

Cand. of Sc. (Chem.) Maksim M. Platonov

(FSUE «VIAM» SRC RF),

Cand.of Sc. (Tech.) G.N. Petrova, S.A. Larionov

15:10–15:20

Structure features of Ti-Nb alloy produced by electric-arc melting and selective laser melting

 

Dr. of Sc. (Physics & Math.) Yuri P. Sharkeev

(National Research Tomsk Polytechnic University),
Cand.of Sc. (Tech.) Zh.G. Kovalevskaya, M.A. Khimich,
Cand.of Sc.
(Tech.) A.A. Saprykin, Е.А. Ibragimov

15:20–15:30

Enhancement of performance characteristics of articles from composite material based on heat-resistant alloy produced by laser additive technology

 

Cand.of Sc. (Tech.) Roman S. Tretyakov

(Bauman Moscow State Technical University),

Professor, Dr. of Sc. (Tech.) A.G. Grigoryants, M.V. Lukyanov,
Professor, Dr. of Sc. (Tech.) I.N. Shiganov,
A.A. Shelestova, A.A. Aleksandrova

15:30–16:00

Coffee-break

16:00–16:10

Additive production in the world: present-day and the future

 

Cand. of Sc. (Physics & Math.) Denis S. Podsoblyaev

(OJSC «Engineering Company AB «Universal»),

A.V. Boyarintsev

16:10–16:20

Fatigue properties of heat-resistant materials produced by SLM

 

Mikhail A. Gorbovets

(FSUE «VIAM» SRC RF),

Cand.of Sc. (Tech.) A.G. Evgenov, I.A. Khodinev, M.I. Lukyanova

16:20–16:30

New technology for production of powders of stainless steels are suitable for use in additive

 

Cand.of Sc. (Tech.) Oksana А. Arzhatkina
(JSC «Leading scientific-research institute of chemical technology»),

Doctor of Sc. (Econ.) A.V. Ivakin, Cand.of Sc. (Tech.) A.V. Samokhin, O.V. Tokareva

16:30–16:40

Experience on application of SLA and SLS additive technologies for production of parts of aerodynamic models with especially compound shape

 

Professor, Dr. of Sc. (Tech.) Vladimir D. Vermel

(FSUE«TsAGI» SRC RF,

Academician of RAS V.Ya. Panchenko, M.M. Novikov,
V.V. Zinyaev, A.L. Puchenkov )

16:40–16:50

Application of plasma-electrolytic process for finish-machining articles produced by the method of selective laser melting

 

Cand.of Sc. (Tech.) Ramil N. Kashapov

(Kazan Federal University)

Dr. of Sc. (Tech.) N.F. Kashapov, L.N. Kashapov, I.S. Golovunin

16:50–17:00

Topological optimization of load-bearing structure in CADFEM Topology optimization

 

Eugene A. Kishov

(CJSC «CADFEM-CIS»)

17:00–17:10

Twenty years of development of SLM at Samara branch of FIAN: achievements and prospects

 

Professor, Dr. of Sc. (Physics & Math.) Igor V. Shishkovski

(P.N. Lebedev Physical Institute of RAS)

17:10–17:20

About possibility of production of additive ceramic structures using fused deposition method

 

Cand.of Sc. (Tech.) Vladimir V.  Promakhov

(National Research Tomsk State University),

Cand.of Sc. (Tech.) I.A. Zhukov, Cand.of Sc. (Tech.) S.A. Vorozhtsov, M.V. Shevchenko,
B.G. Tretyakov, Dr. of Sc. (Physics & Math.)  A.S. Zhukov,

 Dr. of Sc. (Physics & Math.) A.B. Vorozhtsov

17:20–17:30

Research of forming process of details and blank parts using fused deposition method

 

Ekaterina A. Shestakova

(OJSC «KAI-LASER»),

Cand.of Sc. (Tech.) R.M. Yanbaev, Cand.of Sc. (Tech.) F.M. Yanbaev, A.Yu. Galdina

17:30–17:40

Implementation of industrial technology of heterogeneous powder laser metallurgy into PJSC «Kuznetsov» for production of engine parts NK-36ST

 

Eugene Yu. Schedrin

(PJSC «Kuznetsov»),

N.I. Yakushin, A.S. Popov, Dr. of Sc. (Tech.) G.A. Turichin,
F.A. Shamrai, D.Yu. Kolodyazhniy

17:40–17:50

Discussion and decision making

 

 

Section № 2

"Equipment, non-destructive control,

and modeling of additive technologies"

(Blue room)

Head of section:

Alexey Dub – Professor, Ph.D., First Deputy

General Director of JSC "Science and innovations"

 

Scientific Secretary:

Mikhail M. Bakradze, Ph.D., head of laboratory

"The deformation and processing of materials under pressure"

FSUE "VIAM" SSC Russia

 

13:00–13:10

The program of development of additive technologies SC "Rosatom":

status and prospects

 

Professor, Dr.Alexey V. Dub

(JSC "Science and innovations")

13:10–13:20

Development of equipment and additive technologies for production of  parts of gas-turbine engines on the basis of heterophasic powder metallurgy

 

  Ph.D. Gleb A. Turichin

(“Peter the Great St. Petersburg

Polytechnic University  "),

Ph.D.  E. V. Zemlyakov,Ph.D. O. G. Klimova, K. D. Babkin,

Dr. A.Ya. Trajanov, Ph.D., P. V. Petrovsky,

Ph.D. D.Yu. Kolodyazhny, F. A. Shamrai,

N. I. Yakushin, E. Yu. Shchedrin

13:20–13:30

The formation of laser beams in optical systems of machines of selective laser melting

 

Ph.D. Dietrich Fidel

(Jülich Research center, Germany),

Dr. Alexander Laskin, doctor-engineer Wilfried Ber,

Professor, Dr. Galeb Natur

13:30–13:40

Modeling of thermal conditions for formation of new phases when joining dissimilar materials

 

Professor, Ph.D. Anna G. Knyazeva

( Tomsk National research

Polytechnic University),

Ph.D. C. N. Sorokova, K. A. Aligozhina

13:40–13:50

The technology of laser deposition of metals

 

Benoit Nicolas Jobert

("BeAM", France),

Frederick Lemoullec

13:50–14:00

Method three large-scale  modeling of  selective laser alloying of composite metal powders with pulse processing

 

Ph.D. Mikhail D. Krivilev

(Udmurt State University),

V. E. Ankudinov, G.A.  Gordeev, Ph.D.  S. M. Reshetnikov,

Ph.D. E. V. Haranzhevsky, Ph.D.  P. K. Galenko

14:00–14:10

Theoretical study of radical copolymerization in photopolymer compositions for laser stereolithography

 

Ph.D.  Anatoly N. Nikitin

(ILIT RAS),

S. V. Kamayev, M. A. Markov, M. M. Novikov

14:10–14:20

Additive manufacturing – quality control for aviation and  space industry

 

David Wilkens

("SLM Solutions", Germany)

14:20–14:30

Numerical modeling of the process of sintering of powder under radiation effect in additive manufacturing

 

Ph.D.  Andry E. Stepanov

(OJSC "Kintech laboratory"),

Ph.D. M. V. Bogdanova, Ph.D.  A. V. Zakirov, B. A. Korneev,

Ph.D.  V. D. Levchenko, Ph.D. B. V. Potapkin

14:30–14:40

Three-dimensional unsteady numerical simulation of gas flow in a supersonic nozzle for laser welding

 

Fanis R.Ischakov

(Kazan national research

technical University named after A. N. Tupolev–KAI),

A. N. Lipatov, I. I. Starshova, I. V. Tsivilsky,

Ph.D.  K. Yu. Nagulin, Ph.D.  A.H. Gilmutdinov

14:40–14:50

Modeling of additive technologies: geometric approach

 

Dr. Sergey A. Lychev

( Ishlinsky Institute for problems in mechanics ),

Ph.D.  E. V. Murashkin, Professor, Dr. A. V. Manzhirov

14:50–15:00

The use of robotic  means for non-destructive control in the diagnosis of modern aviation materials

 

Sergei I. Bezgodov

(OJSC "Technovotum"),

A. M. Slyadnev

15:00–15:10

A new paradigm of certification of materials and structures of a new quality, received by advanced production technologies in the "digital factories"

 

Professor, Dr. Andrey E. Ushakov

(Skolkovo Institute of science and technology)

15:10–15:20

Systems of computer-aided design and additive technology for reconstructive replacement surgery

 

Mikhail M. Novikov

(ILIT RAS),

V.V Vnuk, E. V. Ippolitov, S. A. Cherebylo

15:20–15:30

The parallel structure mechanisms for additive production

 

Professor, Dr. Victor A. Glazunov

(Institute of mechinesl science named after

A. A. Blagonravov  of RAS),

P. A. Shvets, N. Yu. Lazarev

15:30–16:00

Coffee-break

16:00–16:10

Powder synthesis technology of complex shaped parts from superalloys AM and PIM: foreign and domestic experience

 

Dr. Alexey B. Semenov

(Bauman Moscow State University),

Professor, Dr.  B. I. Semenov, A. E. Gavrilenko

16:10–16:20

Research the influence  modes of selective laser sintering of intermetallic alloy VKNA

Anton V.Sotov

(Samara State Aerospace University named after S. P. Korolev (NRU)),

Ph.D.  V. G. Smelov, A. V. Agapovichev, Ph.D.  E. A. Nosova

16:20–16:30

Equipment for layer-by-layer production of complex-shaped products by method of selective laser melting MeltMaster3D 550

 

Evgeny V. Tretyakov

(PJSC RPA “CNIITMASH”),

Ph.D. V. V Beregovsky., Ph.D.  S. A. Shchurenkova

16:30–16:40

The methodology of experimental software for entering changes and additions to the existing normative requirements of the safety justification of new structure  quality

 

Ph.D. Ivan V. Sergeichev

( Skolkovo Institute of science and technology),

Professor, Dr. A. E. Ushakov

16:40–16:50

The technology of in-kjet printing in the electronics industry

 

Vitaly P. Kim

(LLC "AkKo Lab"),

Ph.D. S. V. Tkachev, Ph.D.  D. Yu. Kornilov,  Dr. S. P. Gubin

16:50–17:00

Features of PolyJet technology in manufacturing of   complex-shaped products

 

Roman A. Vdovin

(Samara State Aerospace

University named after S. P. Korolev (NRU)),

Ph.D.  V. G. Smelov, T. M. Tomilina, M. M. Laktionova

17:00–17:10

Computer simulation of selective laser melting of carbonyl iron powder

 

George A. Gordeev

(Udmurt State University),

Ph.D.  M. D. Krivilev, V. E. Ankudinov,

Ph.D. E. V. Haranzhevsky, A. A. Bogdanov

17:10–17:20

Additive technologies: equipment for analytical and metrological control of powders and products

 

Nikolay A. Perekopayko

(LLC "Thermo Techno"),

R. V. Greenberg

17:20–17:30

The study of  gas flows  by optical methods in supersonic nozzle for laser welding

 

Fanis R.Iskhakov

(Kazan National Research

Technical University named after A. N. Tupolev–KAI),

A. N. Lipatov, A.I. Shpilev,

Ph.D.   K. Yu. Nagulin, Dr. A.H. Gilmutdinov

17:30–17:40

Problems of training specialists in the field of additive technologies

 

Ph.D.  Nikita V. Martyushev

(Tomsk National research

Polytechnic University"),

Ph.D.  A. N. Yakovlev, Ph.D. K. S. Kostikov, V. V. Fedorov

17:40–17:50

Discussion. The decision-making

 

ROUND TABLE

 

"Improvement of state policy in the field of development of

additive technologies in Russia and the role of technology platforms

in assistance of them accelerate growth "

(Room of Scientific and technical council)

 

Chairman:

Elena V. Buiylova – Chairman of the Board

Association "Technology platform "Modelling and operation technologies of high-tech systems" ("MTEVS")

 

Co-chair:

Olga G. Ospennikova – Ph. D.,

Head of Scientific-Research Bureau   “Heat-resistant casr and wrought alloys and steels, protective coatings for GTE components”

FSUE "VIAM" SRC RF, scientific Secretary of the Expert Council of the Technological platform "Materials and metallurgic technologies"

 

13:00–13:05

Opening of the meeting. Opening address

 

Elena Buiylova
(Association “MTEVS”)

13:05–13:20

The competence and experience of e TP MTM in assistance  of implementation of projects aimed at expansion and development of additive technologies in Russia. Additive technology is the interconnection of science, education and industry

 

Ph.D. Olga G. Ospennikova
(FSUE "VIAM"  SRC RF)

13:20–13:30

The results of the research conducted within the consortium Aviadvigatel–VIAM–IPLIT–SPbSPU, for the manufacture and repair complex-parts of gas turbine engines

Ph.D. Alexander G. Evgenov
(FSUE "VIAM" SRC RF)

13:30–13:40

The possibility of application  of the study results of structural-phase state of heat-resistant nickel alloys during selective laser melting for the tasks of industry, conducted in the frame of the consortium FSUE "VIAM"–Kurchatov Institute -Bauman Moscow State University

 

Ph.D.  Eva A. Lukina

(FSUE "VIAM" SRC RF),

Dr. M. R. Orlov

13:40–13:55

The competence and experience of the Association "TP "MTEVS" in the field of assistance  of  implementation of projects aimed at expansion and development  of additive technologies in Russia

 

Ph.D. Igor V. Tsvetkov

(Association ” MTEVS”

13:55–14:05

The usage of technology and equipment for heterophase growing of parts from heat resistant alloys in engine-manufacture

 

Felix A. Shamray

(JSC "UEC")

14:05–14:15

Development of equipment for layer-by-layer production of complex-shaped products by selective laser melting MeltMaster3D 550

 

Ph.D.  Vladimir V. Beregovskiy

(PJSC RPA “CNIITMASH”)

14:15–14:25

The creation of number of types of domestic machines for additive technologies

 

Dmitriy L. Saprikin

CJSC SRI ESTO

14:25–14:35

Development of a method for producing complex-shaped products from

ceramics with the use of additive technologies

 

Ph.D. Vladimir V. Promahov

(Tomsk National research

state University)

14:35–14:45

Technology and equipment for hybrid forming products

 

Ph.D. Andrey S. Kuznetsov

(FSUE "NAMI" SRC RF),

Ph.D. V. V. Serebryanniy

14:45–14:55

Production technology of wolfram carbide powders on the basis of domestic raw materials for additive technologies

 

Efim N. Pletenev

(CJSC " Wolfram Company")

14:55–15:05

Perspectives of application of additive technologies by high-tech industry companies at the present stage

 

Ph.D. Mikhail V. Gerov

(JSC "Corporation "Moscow Institute of Tjermal Technology")

15:05–15:15

Perspectives of development of small and medium business on the basis of technologies of additive manufacturing

 

Ph.D. Alexander D.  Fertman

(Foundation “Skolkovo”)

15:15–15:30

Discussion of questions of creation of new cooperation between the participants of the round table for the implementation of projects in the field of development of additive technologies

15:30–15:40

Analysis of key issues holding the development  of additive technologies

 

Professor, Dr. Vladimir  N. Chuvildeev

(Lobachevsky State University of Nizhni Novgorod)

15:40–16:00

Discussion of effective instruments of state support for implementation of projects in the field of development additive technologies. The decision-making

 

Poster session

(lobby of Large conference hall)

12:00-16:00

 

1

Manufacture of parts and components of rotating sprayer of liquid by the method of layer-by-layer welding

 

Ph.D.  Alexey V. Sinkov

(Volzhski Polytechnical Institute),

S. I. Blaginin., E. P. Boytsov, A. P. Kabakov

2

Process of modeling of supporting structures and their optimization for details produced by the method of layer-by-layer laser alloying

 

Pavel B. Mazalov

(FSUE "VIAM" SRC RF),

S. V. Nerush, A. M. Rogalev

3

Additive manufacturing of nickel aluminide by method of three-dimensional laser welding

 

Dmitriy V. Kotoban

(MSTU "STANKIN"),

Dr. I. V. Shishkovsky, I. Yu. Smurova

4

Research of technological features of the process of the blade processing of details and and workpieces obtained by different methods of additive technologies

 

Dmitry V. Kurylev

(OJSC "KAI-LASER"),

Ph.D.  R. M. Yanbaev, Dr. A. N. Lunev

5

Powder composition of TiC–Ti for usage in additive technologies

 

Maxim G. Krinitsin

(Tomsk National research

Polytechnic University),

G. A. Pribytkov

6

Comparison of constructions made by using of additive technologies with stone masonry

 

Vladimir V. Polozenko

(State Specialized Planning Institute)

7

Development of the technology of selective laser melting composite powder materials with solid content of hardening phases

 

Roman S. Khmyrov

(MSTU "STANKIN"),

Dr. A. V. Gusarov, Ph.D. T. V. Tarasova

8

The use of the technology of direct laser growth for the manufacturing of stainless steel specimens and study of their mechanical properties

 

Dmitry P. Bykovsky

(National Research Nuclear University “MEPhI”),

 Ph.D. V. N. Petrovsky, Ph.D. A. V. Osintsev,

K. Y. Ochkov, Ph. D. A. N. Solonin, I. S. Popkova

9

The technology for producing workpiece hyperboloidal gears of the double curvature by the layer-by-layer growth on 3D printers

 

Mikhail  V. Pechenkin

(JSC "KAI-LASER"),

Dr. A. N. Lunev, Ph.D. R. M. Yanbaev

10

The capabilities of additive manufacturing technologies for the manufacture of engineering products of different destination

 

Ph.D. Tatiana V. Tarasova

(MSTU "STANKIN"),

A. A. Filatova

11

The formation of coatings from stainless steel by additive method of supersonic laser deposition

 

Ph. D. Andrey I. Gorunov

(Kazan National Research

Technical University named after A. N. Tupolev-KAI),

A.I. Gorunov, E. S. Popov, Dr. A. A. Gilmutdinov

12

Synthesis of intermetallic compounds by laser in coatings obtained by cold gas-dynamic spraying

 

Pavel A. Podrabinnik

(MSTU "STANKIN"),

Dr. I. V. Shishkovsky, Ph.D. T. V. Tarasova

13

The development of the concept of "rapid" monitoring and control of the technological process of pultrusion based on mathematical modeling methods for the purpose of ensuring projected target quality of profiles from PCM

 

Ph.D. Alexander  A. Safonov

(SKOLKOVO Institute of Science and Technology),

Professor A. E. Ushakov, A. A. Saratov

14

The modeling of the manufacture technology of products from composite materials based on thermoplastic binders. The determination of the conditions of defect nucleation

Ph.D. Boris N. Fedulov

(SKOLKOVO Institute of Science and Technology),

M. M. Kantor, A. A. Safonov

15

Simulation of temperature fields during sintering of the copper powder by SLS method

 

Egor A. Ibragimov

(Yurga Technological Institute of Tomsk

Polytechnic University),

Ph.D. S. S. Saprykin, Ph.D. N. A. Saprykina, E. V. Babakova

16

Optical diagnostics of the process of selective laser melting

 

Ivan V. Zhirnov

(MSTU "STANKIN"),

I. Yu. Smurov, M.A. Dubenskaya, V. I. Teleshevsky

17

The study of gas-powder flow in off-axis nozzle for laser cladding by optical methods

 

Fanis R.  Iskhakov

(Kazan National Research

Technical University named after A. N. Tupolev-KAI),

A. N. Lipatov, A. I. Shpilev,

Ph.D. K. Yu. Nagulin, Dr. A. H. Gilmutdinov

18

 

The results of joint work of JSC "Stankoprom" and JSC "Center for

additive technologies" on introduction of additive technologies in machine-building industry

 

Boris P. Salamahin

(JSC "Stankoprom", JSC "Center of additive technology"),

Dr. A. P. Kuznetsov, N. M. Tokarev, V. A. Kukushkin 

19

Laser synthesis from copper powder PMS-1

 

Ph. d. Alexander A. Saprykin

(Yurga Technological Institute of

Tomsk Polytechnic University),

Ph.D. N. A. Saprykina, E. A. Ibragimov